New lager session Saturday
Moderator: Brandon
- Owenbräu
- German Brewing
- Posts: 1196
- Joined: Tue Dec 22, 2015 8:23 pm
- Crunk
- Assistant Brewer
- Posts: 252
- Joined: Sun Mar 19, 2017 6:36 am
Re: New lager session Saturday
The bug I had for brewing has now turned into a monster, the visual efficiency of the system without doing any calculations is remarkable, the boil off, steam loss, etc.. I can't believe it, and frankly, I wouldn't, if I had not seen it with my own eyes. I have been taking thorough notes from the start. More to follow.
Striving to brew better beer every time
- Crunk
- Assistant Brewer
- Posts: 252
- Joined: Sun Mar 19, 2017 6:36 am
Re: New lager session Saturday
Taste is way better, I need adjust my water now, my system isn't loosing as it was before I missed my number Alittle, so this batch will be drinkable but a test and learning batch for sure, but it seems to like it will be my best batch yet. The pH stayed in line the entire time I had to do no additions whatsoever
Striving to brew better beer every time
- Crunk
- Assistant Brewer
- Posts: 252
- Joined: Sun Mar 19, 2017 6:36 am
Re: New lager session Saturday
After crunching my numbers, I have established points of efficiency concerns that I will address immediately, along with more adjustments that I would like to make to the system, to improve on the limitations of air ingress.
I took the time compare the flavors of what I'm looking for, and what I currently drink, the similarity is incredibly closers to what I'm trying to achieve.
The wort going to the fermentor was considerably clearer than any other batch that I have brewed.
The cleaning process afterwards, was also considerably easier for reasons I can only contribute to a sealed system keeping all of the solid material moist.
The final aroma from my sample pulled from the sample port was outstanding, I filled my fermentor through the sample port to keep air out, I also put my grain into the mash tun sealed it and filled it from the bottom port to keep air out, I didn't have nitrogen to purge it, YET.
That is all for now.
I took the time compare the flavors of what I'm looking for, and what I currently drink, the similarity is incredibly closers to what I'm trying to achieve.
The wort going to the fermentor was considerably clearer than any other batch that I have brewed.
The cleaning process afterwards, was also considerably easier for reasons I can only contribute to a sealed system keeping all of the solid material moist.
The final aroma from my sample pulled from the sample port was outstanding, I filled my fermentor through the sample port to keep air out, I also put my grain into the mash tun sealed it and filled it from the bottom port to keep air out, I didn't have nitrogen to purge it, YET.
That is all for now.
Striving to brew better beer every time
- Weizenberg
- German Brewing
- Posts: 843
- Joined: Wed Nov 11, 2015 2:11 pm
- Contact:
Re: New lager session Saturday
Ahem, you need oxygen for good fermentation. Once the yeast is added, oxygen is not a concern. You need to propagate it a little though, to ensure it's fully active when pitched.
The Quest for Edelstoff - http://edelstoffquest.wordpress.com
- Crunk
- Assistant Brewer
- Posts: 252
- Joined: Sun Mar 19, 2017 6:36 am
Re: New lager session Saturday
I added 2 minutes, of pure co2 to the wort before I pitched.
Striving to brew better beer every time
- Weizenberg
- German Brewing
- Posts: 843
- Joined: Wed Nov 11, 2015 2:11 pm
- Contact:
Re: New lager session Saturday
do you have a reading?
The Quest for Edelstoff - http://edelstoffquest.wordpress.com
- Crunk
- Assistant Brewer
- Posts: 252
- Joined: Sun Mar 19, 2017 6:36 am
Re: New lager session Saturday
I don't have my do meter yet or my books ordered from vlb, so I do not have a measured amount, I did time the injection of o2 I added from a disposable bottle and wand with aeration Stone for 2 minutes, it created a 1/4 inch small foam head on top of the wort just like head on a poured beer as I use low pressure I don't open the bottle all the way
If I were to guess, I would say 10 to 12 mg/l
I plan on installing a wort wizard, or some custom variation.
Any techniques, or suggestions for upgrading this process would be appreciated.
If I were to guess, I would say 10 to 12 mg/l
I plan on installing a wort wizard, or some custom variation.
Any techniques, or suggestions for upgrading this process would be appreciated.
Striving to brew better beer every time
- Weizenberg
- German Brewing
- Posts: 843
- Joined: Wed Nov 11, 2015 2:11 pm
- Contact:
Re: New lager session Saturday
With pure oxygen it is very easy to overdo it, inducing a unfavourable environment for the yeast (>34 mgl).
A flow meter is highly recommended. Mine came from an ambulance, but the ones available for welding gases are also perfectly acceptable..
I don't use these aeration stones, instead I use Venturi tubes for in-line mixing. These can be obtained rather cheaply via eBay.
Pure O2 will require monitoring. Once you have a DO meter you will see how easy it is to overshoot and how hard it is to estimate without knowing the flow rate.
A flow meter is highly recommended. Mine came from an ambulance, but the ones available for welding gases are also perfectly acceptable..
I don't use these aeration stones, instead I use Venturi tubes for in-line mixing. These can be obtained rather cheaply via eBay.
Pure O2 will require monitoring. Once you have a DO meter you will see how easy it is to overshoot and how hard it is to estimate without knowing the flow rate.
The Quest for Edelstoff - http://edelstoffquest.wordpress.com
- Owenbräu
- German Brewing
- Posts: 1196
- Joined: Tue Dec 22, 2015 8:23 pm
Re: New lager session Saturday
A local lager brewery uses a commercial air compressor to aerate their wort. They inject inline during transfer to the CCV, then blast air into the fermentor from the bottom port until 8-10 ppm is achieved. The nice thing about ambient air, is you cannot supersaturate the wort.
- The best do the basics better -
Who is online
Users browsing this forum: No registered users and 12 guests