IPA/PA - LODO effects?
Moderator: Brandon
- Feurhund
- Posts: 45
- Joined: Sun May 15, 2016 8:09 am
- Location: Newburyport, Massachusetts
IPA/PA - LODO effects?
I am planning on brewing a Hoppy New England style Pale Ale soon. New England style has come to mean hazy, lower bitterness with lots of whirlpool and dry hopping, a good amount of adjuncts (flaked oats/wheat) for mouthfeel and head retention. I.e Hill Farmstead, Trillium, Tree House.
I am wondering what effect LODO would have on a beer like this and knowing that oxygen fades hop aroma and flavor, if it might improve it.
Thank you for your input!
I am wondering what effect LODO would have on a beer like this and knowing that oxygen fades hop aroma and flavor, if it might improve it.
Thank you for your input!
- Owenbräu
- German Brewing
- Posts: 1196
- Joined: Tue Dec 22, 2015 8:23 pm
Re: IPA/PA - LODO effects?
Unoxidized malts and hops are delicious
- The best do the basics better -
- Feurhund
- Posts: 45
- Joined: Sun May 15, 2016 8:09 am
- Location: Newburyport, Massachusetts
Re: IPA/PA - LODO effects?
- image.jpeg (1.68 MiB) Viewed 7449 times
Well, it worked! This beer has 10% flaked red wheat and 10% flaked oats with the rest crisp pale ale malt.
Saturated with Citra, Mosaic and Galaxy and fermented with both Conan(heady topper strain) and London ale III.
Hops come through bright and clear and the mouthfeel is silky and full but not heavy. The malt is there too with a pleasant fresh grain backbone. LODO definitely improved the beer all around. Glad I went 10 gallons on this batch.
- Brody
- Assistant Brewer
- Posts: 326
- Joined: Sat Nov 14, 2015 11:30 pm
- Location: Philadelphia, Pennsylvania
Re: IPA/PA - LODO effects?
Did you notice any sulfur in the end? I ended up dialing back my sms to 25ppm on ale's (although the jury's out, batch one is still fermenting) after 100ppm was too much.
-
- German Brewing
- Posts: 409
- Joined: Thu Oct 15, 2015 1:45 pm
Re: IPA/PA - LODO effects?
25 mg/l is a little low to offer enough protection IMO, but see how it turns out for you.
I think 40 mg/l is the magic number for a tight no sparge system.
Also remember that the original pdf called for 100 mg/l in mash water and 25 mg/l in sparge water assuming a traditional system. If you use 100 mg/l in a no sparge system, that's a lot more total sulfite than the traditional system.
I think 40 mg/l is the magic number for a tight no sparge system.
Also remember that the original pdf called for 100 mg/l in mash water and 25 mg/l in sparge water assuming a traditional system. If you use 100 mg/l in a no sparge system, that's a lot more total sulfite than the traditional system.
If you always do what you've always done, then you'll always get what you've always gotten.
- Brody
- Assistant Brewer
- Posts: 326
- Joined: Sat Nov 14, 2015 11:30 pm
- Location: Philadelphia, Pennsylvania
- Feurhund
- Posts: 45
- Joined: Sun May 15, 2016 8:09 am
- Location: Newburyport, Massachusetts
Re: IPA/PA - LODO effects?
My no sparge 19 gallons of pre boiled water was about 60mg/l no sulfur in the final beer.
-
- German Brewing
- Posts: 409
- Joined: Thu Oct 15, 2015 1:45 pm
Re: IPA/PA - LODO effects?
60 mg/l for no sparge should be fine and I doubt you will get any objectionable sulfur at this dose with most yeasts. Certain yeasts, like wheat beer yeasts, seem to react more unfavorably to residual sulfite so in that case I would reduce the dose a bit.
If you follow the recommended doses in the paper, the mash and sparge averages out to about 60 mg/l overall. So contrary to a lot of what has been said by people not on this forum, the amount of sodium added to the water profile is only about 0.24 * 60 = 14.4 ppm. The 24 ppm sodium is only added to the mash water, but it gets diluted by the sparge water.
40-50 works just as well with my tight system, and in my book the less I need to use the better.
If you follow the recommended doses in the paper, the mash and sparge averages out to about 60 mg/l overall. So contrary to a lot of what has been said by people not on this forum, the amount of sodium added to the water profile is only about 0.24 * 60 = 14.4 ppm. The 24 ppm sodium is only added to the mash water, but it gets diluted by the sparge water.
40-50 works just as well with my tight system, and in my book the less I need to use the better.
If you always do what you've always done, then you'll always get what you've always gotten.
-
- Assistant Brewer
- Posts: 264
- Joined: Mon Apr 25, 2016 10:57 pm
Re: IPA/PA - LODO effects?
Was there any type of dry hop for this beer? If so what procedure was used?
Sent from my SM-G930V using Tapatalk
Sent from my SM-G930V using Tapatalk
- Feurhund
- Posts: 45
- Joined: Sun May 15, 2016 8:09 am
- Location: Newburyport, Massachusetts
Re: IPA/PA - LODO effects?
For the full 10 gallon batch I dry hopped with 1.5oz each of Mosaic, Citra and Galaxy at day 5 of fermentation in the conical.
I then put 1oz each in a paint strainer bag, dropped into a CO2 purged keg and filled.
Hops stay in till keg is kicked.
I then put 1oz each in a paint strainer bag, dropped into a CO2 purged keg and filled.
Hops stay in till keg is kicked.
Who is online
Users browsing this forum: No registered users and 48 guests