Brewtan
Moderator: Brandon
- Weizenberg
- German Brewing
- Posts: 843
- Joined: Wed Nov 11, 2015 2:11 pm
- Contact:
- Futur
- Posts: 22
- Joined: Tue Jul 19, 2016 9:10 pm
Re: Brewtan
I had some interesting findings today during two back to back lodo batches. I have a single vessel BIAB RIMS system with a stainless floating mash cap which I've recently built as I've ditched my grainfather.
Using the dextrose and yeast method for oxygen scavenging I got my strike water down to 0.2ppm before adding a 60mg/L dose of SMB and brewtan B.
For the first time I went to the effort to measure my mash O2 levels and they were not good. Try 2.5ppm straight after dough in, this is on the first batch and didn't increase during the entire mash. I had a slight leak on one of my lines which I thought was the culprit, so I tightened up my system and went again for another batch.
Long story short, I got the same results, low strike water readings then high readings which didn't change throughout the mash. I took the utmost care when doughing in both brews.
After some thought and seeing others having such low DO readings during the mash, I isolated the only difference to be the brewtan b and came up with an experiment to prove it.
I had two jars filled with standard tap water half full (250mL/1cup). I then added 0.1g of SMB to both, then added 0.1g Brewtan to only one jar. Then I filled the jars up to the brim with the remaining tap water (another 250mL/1cup). In addition, I continued to add more SMB to jar 1 to see what the effect would be. I waited about a minute between each addition to let the reactions take place. See the results below.
Jar1
250 mL Tap water only 4.44 ppm
0.1 g SMB 0.20 ppm
0.1 g Brewtan B 0.5ppm
Another 250 mL tap water 2.5 ppm
Another 0.1 g SMB 2.58 ppm
Another 0.5 g SMB 1.32 ppm
Jar 2
250 mL Tap water only 4.50 ppm
0.1 g SMB 0.22 ppm
Measurement when brewtan B added for Jar 1 0.22 ppm
Another 250 mL tap water 0.29 ppm
Measurement when another 0.1 g SMB added for Jar 1 0.3 ppm
Measurement when another 0.5 g SMB added for Jar 1 0.36 ppm
If you can make sense of these results you'll see brewtan b seems to block the effect of SMB when it comes to oxygen scavenging. Either that or brewtan B messes with the DO600 meter somehow. I ran through this experiment twice to ensure it wasn't just a mistake but it was repeatable.
I'm not sure what to think of this right now, but I think for all future batches I'll be keeping brewtan out of my mash and sticking to only SMB for lodo beers.
Cheers!
Using the dextrose and yeast method for oxygen scavenging I got my strike water down to 0.2ppm before adding a 60mg/L dose of SMB and brewtan B.
For the first time I went to the effort to measure my mash O2 levels and they were not good. Try 2.5ppm straight after dough in, this is on the first batch and didn't increase during the entire mash. I had a slight leak on one of my lines which I thought was the culprit, so I tightened up my system and went again for another batch.
Long story short, I got the same results, low strike water readings then high readings which didn't change throughout the mash. I took the utmost care when doughing in both brews.
After some thought and seeing others having such low DO readings during the mash, I isolated the only difference to be the brewtan b and came up with an experiment to prove it.
I had two jars filled with standard tap water half full (250mL/1cup). I then added 0.1g of SMB to both, then added 0.1g Brewtan to only one jar. Then I filled the jars up to the brim with the remaining tap water (another 250mL/1cup). In addition, I continued to add more SMB to jar 1 to see what the effect would be. I waited about a minute between each addition to let the reactions take place. See the results below.
Jar1
250 mL Tap water only 4.44 ppm
0.1 g SMB 0.20 ppm
0.1 g Brewtan B 0.5ppm
Another 250 mL tap water 2.5 ppm
Another 0.1 g SMB 2.58 ppm
Another 0.5 g SMB 1.32 ppm
Jar 2
250 mL Tap water only 4.50 ppm
0.1 g SMB 0.22 ppm
Measurement when brewtan B added for Jar 1 0.22 ppm
Another 250 mL tap water 0.29 ppm
Measurement when another 0.1 g SMB added for Jar 1 0.3 ppm
Measurement when another 0.5 g SMB added for Jar 1 0.36 ppm
If you can make sense of these results you'll see brewtan b seems to block the effect of SMB when it comes to oxygen scavenging. Either that or brewtan B messes with the DO600 meter somehow. I ran through this experiment twice to ensure it wasn't just a mistake but it was repeatable.
I'm not sure what to think of this right now, but I think for all future batches I'll be keeping brewtan out of my mash and sticking to only SMB for lodo beers.
Cheers!
- Owenbräu
- German Brewing
- Posts: 1196
- Joined: Tue Dec 22, 2015 8:23 pm
Re: Brewtan
What is the proposed mechanism of action for blocking SMB?
- The best do the basics better -
-
- German Brewing
- Posts: 409
- Joined: Thu Oct 15, 2015 1:45 pm
Re: Brewtan
Hmm, that's a very interesting idea. I am starting to experiment with 30 mg/l SMB + 30 mg/l BB in my water and so far I haven't taken any DO readings, but anecdotally the wort was just as bright and full flavored (maybe the flavor was even a hair better) as the rest of my LoDO batches that used SMB only.
If you always do what you've always done, then you'll always get what you've always gotten.
- Owenbräu
- German Brewing
- Posts: 1196
- Joined: Tue Dec 22, 2015 8:23 pm
Brewtan
I mostly see differences in clarity and stability of the final product. Flavor has been excellent with and without BB. I'm curious as to what could cause a link between BB and increased DO levels. Air trapped in the powder? It is a PITA to mix and dissolves thoroughly.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
- The best do the basics better -
-
- Braumeister
- Posts: 882
- Joined: Tue Oct 13, 2015 9:27 pm
Re: Brewtan
I have seen a positive impact from using gallontannins, and I will go so far as saying they MUST be used in conjunction when any AA is used. If you are seeing an improvement( as I did) that would suggest fenton reactions from some part of your process. I am all SS and RO, and brilliantly clear wort and still saw it in the kettle alone.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
-German Brewing Founder-
- Owenbräu
- German Brewing
- Posts: 1196
- Joined: Tue Dec 22, 2015 8:23 pm
Re: Brewtan
- The best do the basics better -
- Big Monk
- Assistant Brewer
- Posts: 282
- Joined: Mon Jun 06, 2016 7:29 am
- Location: New York
Re: Brewtan
“We are what we repeatedly do. Excellence, therefore, is not an act, but a habit.” Aristotle
"Messieurs, c’est les microbes qui auront le dernier mot." Louis Pasteur
Check us out at www.lowoxygenbrewing.com
"Messieurs, c’est les microbes qui auront le dernier mot." Louis Pasteur
Check us out at www.lowoxygenbrewing.com
- Big Monk
- Assistant Brewer
- Posts: 282
- Joined: Mon Jun 06, 2016 7:29 am
- Location: New York
Re: Brewtan
“We are what we repeatedly do. Excellence, therefore, is not an act, but a habit.” Aristotle
"Messieurs, c’est les microbes qui auront le dernier mot." Louis Pasteur
Check us out at www.lowoxygenbrewing.com
"Messieurs, c’est les microbes qui auront le dernier mot." Louis Pasteur
Check us out at www.lowoxygenbrewing.com
Who is online
Users browsing this forum: No registered users and 4 guests