Wet Milling Equipment and settings
Moderator: Brandon
- Weizenberg
- German Brewing
- Posts: 843
- Joined: Wed Nov 11, 2015 2:11 pm
- Contact:
Re: Wet Milling Equipment and settings
I'd tighten it a bit more...
Carefully though.
Carefully though.
The Quest for Edelstoff - http://edelstoffquest.wordpress.com
-
- Assistant Brewer
- Posts: 264
- Joined: Mon Apr 25, 2016 10:57 pm
Re: Wet Milling Equipment and settings
Starting to wonder if a 2 roller may be better than a 3 roller for conditioning malt.
Sent from my SM-G930V using Tapatalk
Sent from my SM-G930V using Tapatalk
- Weizenberg
- German Brewing
- Posts: 843
- Joined: Wed Nov 11, 2015 2:11 pm
- Contact:
Re: Wet Milling Equipment and settings
Improved mill setup. I can only recommend powering it via a geared motor than a drill. Makes a world of difference.
- IMG_1222.JPG (2.03 MiB) Viewed 4717 times
The Quest for Edelstoff - http://edelstoffquest.wordpress.com
-
- Assistant Brewer
- Posts: 264
- Joined: Mon Apr 25, 2016 10:57 pm
- Weizenberg
- German Brewing
- Posts: 843
- Joined: Wed Nov 11, 2015 2:11 pm
- Contact:
Re: Wet Milling Equipment and settings
Yes. It's the Klassic, not the Kompact. Same manufacturer. These are the same as used in the teaching labs at Weihenstephan.
The Quest for Edelstoff - http://edelstoffquest.wordpress.com
-
- Assistant Brewer
- Posts: 264
- Joined: Mon Apr 25, 2016 10:57 pm
- Weizenberg
- German Brewing
- Posts: 843
- Joined: Wed Nov 11, 2015 2:11 pm
- Contact:
Re: Wet Milling Equipment and settings
Yes.
I think the monster mills are nice too. It depends what choices one makes and where the emphasis lies. If you can, get a 2 roller with wheels with the biggest diameter as possible.
Conditioning the malt to suppress LOX activity is more important to me than mill specifics though.
A geared motor is a must for those serious about milling. Makes a much ore even crush with less flour than when powered by a drill.
I think the monster mills are nice too. It depends what choices one makes and where the emphasis lies. If you can, get a 2 roller with wheels with the biggest diameter as possible.
Conditioning the malt to suppress LOX activity is more important to me than mill specifics though.
A geared motor is a must for those serious about milling. Makes a much ore even crush with less flour than when powered by a drill.
The Quest for Edelstoff - http://edelstoffquest.wordpress.com
-
- Apprentice Brewer
- Posts: 145
- Joined: Mon Apr 25, 2016 7:28 pm
Re: Wet Milling Equipment and settings
Here is an article about a $30 DIY low RPM motor for milling http://www.homebrewtalk.com/cheap-diy-o ... -mill.html
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
-
- Posts: 9
- Joined: Thu Oct 27, 2016 12:41 pm
Re: Wet Milling Equipment and settings
I'm a hand crank miller (I only brew 2.5 gal batches so it's not too much of a workout). I wonder if there are inconsistencies with my crush due to the changing RPMs as I mill. I conditioned the malt for the first time on my last brew and I particularly liked how the grain bed looked after draining the tun. Nice and fluffy. Also much, much less flour. Whether or not it did anything for my beer? Tough to say as I've changed a lot of variables with inclusion of more low oxygen techniques lately.
- Weizenberg
- German Brewing
- Posts: 843
- Joined: Wed Nov 11, 2015 2:11 pm
- Contact:
Re: Wet Milling Equipment and settings
A 12V motor won't do if you consider the equation at play here (sorry for it being in German)
Leistung P [kw]= Drehzahl n [U/min] * Drehmoment M [Nm] / faktor 9550
Most mills will need 6Nm nominal torque, whereas the startup torque can be anything up to 25Nm. A simple single phase 2 pole motor with a 1:10 gearbox will do much better. If you want the Rolls Royce, then a 3 Phase motor controlled by an Inverter Drive would be the best setup possible.
One thing I noticed is that a motor will produce a much more even crush and substantially less flour. It's definitively a huge improvement for me, but I've managed quite happily without one before.
Note that none of what is being discussed here is a wet milling setup. Wet milling is something else than what is discussed here, dry milling with conditioning would be the accurate terminology.
If one doesn't condition the grain with water of at least 80C, I see very little point in doing so. Then one might just as well mill without conditioning.
Leistung P [kw]= Drehzahl n [U/min] * Drehmoment M [Nm] / faktor 9550
Most mills will need 6Nm nominal torque, whereas the startup torque can be anything up to 25Nm. A simple single phase 2 pole motor with a 1:10 gearbox will do much better. If you want the Rolls Royce, then a 3 Phase motor controlled by an Inverter Drive would be the best setup possible.
One thing I noticed is that a motor will produce a much more even crush and substantially less flour. It's definitively a huge improvement for me, but I've managed quite happily without one before.
Note that none of what is being discussed here is a wet milling setup. Wet milling is something else than what is discussed here, dry milling with conditioning would be the accurate terminology.
If one doesn't condition the grain with water of at least 80C, I see very little point in doing so. Then one might just as well mill without conditioning.
The Quest for Edelstoff - http://edelstoffquest.wordpress.com
Who is online
Users browsing this forum: No registered users and 76 guests